Exactly How to Install a Bath Tub Yourself
Exactly How to Install a Bath Tub Yourself
Blog Article
This great article below involving A Step-by-Step Guide to Installing a Bathtub is exceedingly attention-grabbing. You should investigate it.
Installing a tub isn't exactly brain surgery, yet it does need strong plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bathtub with a brand-new one is additionally a moderately challenging job. If the old bathtub is readily available, the job can relocate speedily; if you have to open a wall surface to get rid of the old bathtub and position the new tub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to move out the old tub and also embeded in the new one. Make certain you have actually qualified yourself for the job as well as fit trying it. Rather than employing a specialist to take control of a halfway-completed task, it is much better to consider employing one before you begin. Possibilities are you might require a professional plumber to make tube connections.
This short article will certainly assist you mount a brand-new bathtub in your bathroom if you have already bought a new tub and don't need to change the arrangement of your previous water supply pipelines.
Your devices as well as material checklist need to comprise the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your setup, after that the first thing you must do is detach the water system. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing faucets can be rather troublesome because of the restricted gain access to that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a towel prepared for the remaining water that will originate from the pipelines. When the supply pipes have actually been eliminated, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from turning during this procedure. As soon as the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Prior to carrying on to fit the new taps, contrast the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic port to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin ensuring that the washers are in area in between the tap and the sink. Safeguard the tap in position with the producer provided backnut. Once the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal faucet ports. The former kind ought to be linked to the faucet ends first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bathtub
Making use of the two wooden boards under its feet, position the bathtub in the needed placement. The wood boards are handy in uniformly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four little points.
The next objective is to guarantee that the tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the tub till the level reads level.
To set up faucets, fit all-time low of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression join; then do the same for the various other faucet.
Switch on the water system and also check all joints as well as brand-new pipework for leakages and tighten them if needed. Load the bathtub and likewise examine the overflow outlet and the typical electrical outlet for leaks.
Finally, take care of the bathroom paneling as described in the manufacturer's instruction manual. Tiling as well as securing around the tub must wait till the bathtub has been utilized a minimum of when as this will certainly resolve it into its final setting.
Getting ready for the Setup
To start with, the sustaining frame provided with the bathroom must be fitted (if called for) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to ensure that if the tap includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last placement.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to split a stiff seal, triggering the water to penetrate the wall in between the bath and the tiling, bring about issues with dampness and also possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components as well as installations. They are offered in tubes and also cartridges, as well as can securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill the tub with water before securing, to allow for the activity experienced when the bathtub is in usage. The sealant can split fairly very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly available on the marketplace. It is recommended to fit the floor tiles using waterproof or waterproof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate reading up on How to Install a Bathtub Yourself? Try leaving a short review directly below. We will be pleased to listen to your opinions about this review. We are looking forward that you come back again soon. You should take a moment to promote this write-up if you liked it. I praise you for your time. Please pay a visit to our site back soon.
Order Repair
Report this page